home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Internet Info 1993
/
Internet Info CD-ROM (Walnut Creek) (1993).iso
/
inet
/
internet-drafts
/
draft-ietf-pppext-lcpmib-01.txt
< prev
next >
Wrap
Text File
|
1993-03-03
|
60KB
|
2,027 lines
Internet Draft
The Definitions of Managed Objects for
the Link Control Protocol of
the Point-to-Point Protocol
27 July 1992
Frank Kastenholz
FTP Software, Inc
26 Princess Street
Wakefield, Mass 01880 USA
kasten@ftp.com
Status of this Memo
This document is an Internet Draft. Internet Drafts are
working documents of the Internet Engineering Task Force
(IETF), its Areas, and its Working Groups. Note that other
groups may also distribute working documents as Internet
Drafts.
Internet Drafts are draft documents valid for a maximum of six
months. Internet Drafts may be updated, replaced, or
obsoleted by other documents at any time. It is not
appropriate to use Internet Drafts as reference material or to
cite them other than as a ``working draft'' or ``work in
progress.'' Please check the 1id-abstracts.txt listing
contained in the internet-drafts Shadow Directories on
nic.ddn.mil, nnsc.nsf.net, nic.nordu.net, ftp.nisc.sri.com, or
munnari.oz.au to learn the current status of any Internet
Draft.
Internet Draft PPP/LCP MIB July 1992
This document will be submitted to the Internet Activities
Board as a Draft Standard. This document defines an
experimental extension to the SNMP MIB. Upon publication as a
Draft Standard, a new MIB number will be assigned. This is a
working document only, it should neither be cited nor quoted
in any formal document.
This document will expire before 1 Feb. 1993.
Distribution of this document is unlimited.
Please send comments to the author.
1. Abstract
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management
protocols in TCP/IP-based internets. In particular, it
describes managed objects used for managing the Link Control
Protocol and Link Quality Monitoring on subnetwork interfaces
that use the family of Point-to-Point Protocols[8, 9, 10, 11,
& 12].
This memo does not specify a standard for the Internet
community.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 2]
Internet Draft PPP/LCP MIB July 1992
2. The Network Management Framework
The Internet-standard Network Management Framework consists of
three components. They are:
RFC 1155 which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of
management. RFC 1212 defines a more concise description
mechanism, which is wholly consistent with the SMI.
RFC 1156 which defines MIB-I, the core set of managed
objects for the Internet suite of protocols. RFC 1213,
defines MIB-II, an evolution of MIB-I based on
implementation experience and new operational
requirements.
RFC 1157 which defines the SNMP, the protocol used for
network access to managed objects.
The Framework permits new objects to be defined for the
purpose of experimentation and evaluation.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 3]
Internet Draft PPP/LCP MIB July 1992
3. Objects
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. Objects in the
MIB are defined using the subset of Abstract Syntax Notation
One (ASN.1) [3] defined in the SMI. In particular, each
object has a name, a syntax, and an encoding. The name is an
object identifier, an administratively assigned name, which
specifies an object type. The object type together with an
object instance serves to uniquely identify a specific
instantiation of the object. For human convenience, we often
use a textual string, termed the OBJECT DESCRIPTOR, to also
refer to the object type.
The syntax of an object type defines the abstract data
structure corresponding to that object type. The ASN.1
language is used for this purpose. However, the SMI [1]
purposely restricts the ASN.1 constructs which may be used.
These restrictions are explicitly made for simplicity.
The encoding of an object type is simply how that object type
is represented using the object type's syntax. Implicitly
tied to the notion of an object type's syntax and encoding is
how the object type is represented when being transmitted on
the network.
The SMI specifies the use of the basic encoding rules of ASN.1
[4], subject to the additional requirements imposed by the
SNMP.
3.1. Format of Definitions
Section 5 contains the specification of all object types
contained in this MIB module. The object types are defined
using the conventions defined in the SMI, as amended by the
extensions specified in [5,6].
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 4]
Internet Draft PPP/LCP MIB July 1992
4. Overview
4.1. Object Selection Criteria
To be consistent with IAB directives and good engineering
practice, an explicit attempt was made to keep this MIB as
simple as possible. This was accomplished by applying the
following criteria to objects proposed for inclusion:
(1) Require objects be essential for either fault or
configuration management. In particular, objects for
which the sole purpose was to debug implementations were
explicitly excluded from the MIB.
(2) Consider evidence of current use and/or utility.
(3) Limit the total number of objects.
(4) Exclude objects which are simply derivable from others in
this or other MIBs.
4.2. Structure of the PPP
This section describes the basic model of PPP used in
developing the PPP MIB. This information should be useful to
the implementor in understanding some of the basic design
decisions of the MIB.
The PPP is not one single protocol but a large family of
protocols. Each of these is, in itself, a fairly complex
protocol. The PPP protocols may be divided into three rough
categories:
Control Protocols
The Control Protocols are used to control the operation
of the PPP. The Control Protocols include the Link
Control Protocol (LCP), the Password Authentication
Protocol (PAP), the Link Quality Report (LQR), and the
Challenge Handshake Authentication Protocol (CHAP).
Network Protocols
The Network Protocols are used to move the network
traffic over the PPP interface. A Network Protocol
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 5]
Internet Draft PPP/LCP MIB July 1992
encapsulates the datagrams of a specific higher-layer
protocol that is using the PPP as a data link. Note that
within the context of PPP, the term "Network Protocol"
does not imply an OSI Layer-3 protocol; for instance,
there is a Bridging network protocol.
Network Control Protocols (NCPs)
The NCPs are used to control the operation of the Network
Protocols. Generally, each Network Protocol has its own
Network Control Protocol; thus, the IP Network Protocol
has its IP Control Protocol, the Bridging Network
Protocol has its Bridging Network Control Protocol and so
on.
This document specifies the objects used in managing one of
these protocols, namely the Link Control Protocol and Link
Quality Monitoring Protocol.
4.3. MIB Groups
Objects in this MIB are arranged into several MIB groups.
Each group is organized as a set of related objects.
These groups are the basic unit of conformance: if the
semantics of a group is applicable to an implementation then
all objects in the group must be implemented.
The PPP MIB is organized into several MIB Groups, including,
but not limited to, the following groups:
o The PPP Link Group
o The PPP LQR Group
o The PPP LQR Extensions Group
o The PPP IP Group
o The PPP Bridge Group
o The PPP Security Configuration Group
o The PPP CHAP Group
o The PPP PAP Group
This document specifies the following groups:
The PPP Link Group
This group represents the lowest "level" of the PPP
protocol.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 6]
Internet Draft PPP/LCP MIB July 1992
This group contains two tables, one containing status
information and the other configuration information. The
configuration table is split off of the status so that it
may be placed in a separate MIB View for security
purposes.
Implementation of this group is mandatory for all PPP
implementations.
The PPP LQR Group
This group provides the basic MIB variables that apply to
the PPP LQR Protocol. This group provides MIB access to
the information required for LQR processing. This group
contains two tables, one containing status information
and the other configuration information. The
configuration table is split off of the status so that it
may be placed in a separate MIB View for security
purposes.
Implementation of the PPP LQR Group is mandatory for all
PPP implementations that implement LQR.
The PPP LQR Extensions Group
The PPP LQR Extensions group contains the most recently
received LQR packet, as well as the "save" fields that
are "logically appended"[12] to received LQR packets.
This is done in order to facilitate external
implementations of the Link Quality Monitoring policies.
It is not practical to examine the relevant MIB objects
which are used to generate LQR packets since LQR policies
may require synchronization of the values of all data
used to determine Link Quality; i.e., the values of the
relevant counters must all be taken at the same instant
in time. Thus, by recording the last received LQR
packet, a synchronized record of the relevant data is
available.
As this information may not be efficiently maintained on
all PPP implementations, implementation of this group is
optional.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 7]
Internet Draft PPP/LCP MIB July 1992
4.4. Relationship to Interface and Interface Extensions
Groups
The PPP Mib is a medium-specific extension to the standard
MIB-2 interface group[2] and to the Interface Extensions MIB
[7]. This section discusses certain components of these
groups when the interface is a PPP interface.
The entire PPP instance represents a single interface in the
sense used in [2] and thus has a single entry in the ifTable.
All PPP packets are defined in [8] as being broadcast packets.
Thus, the packets are counted as non-unicast packets in the
ifTable (ifInNUcastPkts and ifOutNUCastPkts) and as broadcasts
in the ifExtnsTable (ifExtnsBroadcastsReceivedOks and
ifExtnsBroadcastsTransmittedOks).
ifSpecific
Contains the OBJECT IDENTIFIER ppp.
ifAdminStatus
Setting this object to up will inject an administrative
open event into the LCP's finite state machine. Setting
this object to down will inject an administrative close
event into the LCP's finite state machine.
The use of the testing value is beyond the scope of this
document.
ifOperStatus
Represents the state of the LCP Finite State Machine. If
the Finite State Machine is in the Opened state then the
value of ifOperStatus is up, otherwise the value of
ifOperStatus is down.
The meaning of the testing value is beyond the scope of
this document.
Per the SNMP Protocol Specification, [15], the linkUp and
linkDown traps apply to the PPP Protocol entity. When the
LCP's Finite State Machine attains the Opened state, a linkUp
trap should be sent. When the Finite State Machine leaves the
Opened state, a linkDown trap should be sent.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 8]
Internet Draft PPP/LCP MIB July 1992
Some tests for the link are defined in this document.
Execution of these tests does not place the link's
ifOperStatus in the testing state as these tests do not
prevent normal data transmission from occuring over the link.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 9]
Internet Draft PPP/LCP MIB July 1992
5. Definitions
RFCppp-MIB DEFINITIONS ::= BEGIN
IMPORTS
experimental, Counter
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
TRAP-TYPE
FROM RFC-1215;
-- PPP MIB
ppp OBJECT IDENTIFIER ::= { experimental 18 }
-- The individual Groups within the PPP MIB
-- This document contains the LCP MIB and
-- as such is common to all PPP inplementations
-- so doing these common OBJECT IDENTIFIER
-- definitions here makes some sense.
--
pppLink OBJECT IDENTIFIER ::= { ppp 1 }
pppLqr OBJECT IDENTIFIER ::= { ppp 2 }
pppIp OBJECT IDENTIFIER ::= { ppp 3 }
pppBridge OBJECT IDENTIFIER ::= { ppp 4 }
pppSecurity OBJECT IDENTIFIER ::= { ppp 5 }
pppTests OBJECT IDENTIFIER ::= { ppp 6 }
--
-- The following are place holders for later
-- elements of the PPP MIBs. When the
-- indicated encapsulation is finished, the
-- MIB for that encapsulation will be placed
-- under the given OID.
--
pppIpx OBJECT IDENTIFIER ::= { ppp 7 }
pppIso OBJECT IDENTIFIER ::= { ppp 8 }
pppAppleTalk OBJECT IDENTIFIER ::= { ppp 9 }
pppDECNet OBJECT IDENTIFIER ::= { ppp 10 }
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 10]
Internet Draft PPP/LCP MIB July 1992
5.1. PPP Link Group
--
-- The PPP Link Group. Implementation of this
-- group is mandatory for all PPP entities.
--
pppLinkStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppLinkStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table containing PPP-link specific variables
for this PPP implementation."
::= { pppLink 1 }
pppLinkStatusEntry OBJECT-TYPE
SYNTAX PppLinkStatusEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Management information about a particular PPP
Link."
INDEX { pppLinkStatusIndex }
::= { pppLinkStatusTable 1 }
PppLinkStatusEntry ::= SEQUENCE {
pppLinkStatusIndex
INTEGER,
pppLinkStatusPhysicalIndex
INTEGER,
pppLinkStatusBadAddresses
Counter,
pppLinkStatusBadControls
Counter,
pppLinkStatusPacketTooLongs
Counter,
pppLinkStatusBadFCSs
Counter,
pppLinkStatusLocalMRU
INTEGER,
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 11]
Internet Draft PPP/LCP MIB July 1992
pppLinkStatusRemoteMRU
INTEGER,
pppLinkStatusLocalToPeerACCMap
OCTET STRING,
pppLinkStatusPeerToLocalACCMap
OCTET STRING,
pppLinkStatusLocalToRemoteProtocolCompression
INTEGER,
pppLinkStatusRemoteToLocalProtocolCompression
INTEGER,
pppLinkStatusLocalToRemoteACCompression
INTEGER,
pppLinkStatusRemoteToLocalACCompression
INTEGER,
pppLinkStatusTransmitFcsSize
INTEGER,
pppLinkStatusReceiveFcsSize
INTEGER
}
pppLinkStatusIndex OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each PPP link. Its value
ranges between 1 and the value of ifNumber. The
interface identified by a particular value of
this index is that identified by the same value
of an ifIndex object instance. The value for
each link must remain constant at least from
one re-initialization of the entity's network
management system to the next
re-initialization."
::= { pppLinkStatusEntry 1 }
pppLinkStatusPhysicalIndex OBJECT-TYPE
SYNTAX INTEGER(0..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of ifIndex that identifies the
interface over which this PPP Link is
operating. This interface would usually be an
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 12]
Internet Draft PPP/LCP MIB July 1992
HDLC or RS-232 type of interface. If there is
no lower-layer interface element, or there is
no ifEntry for the element, or the element can
not be identified, then the value of this
object is 0."
::= { pppLinkStatusEntry 2 }
pppLinkStatusBadAddresses OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets received with an
incorrect Address Field. This counter is a
component of the ifInErrors variable that is
associated with the interface that represents
this PPP Link."
REFERENCE
"Section 3.1, Address Field, of RFC1331."
::= { pppLinkStatusEntry 3 }
pppLinkStatusBadControls OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets received on this link
with an incorrect Control Field. This counter
is a component of the ifInErrors variable that
is associated with the interface that
represents this PPP Link."
REFERENCE
"Section 3.1, Control Field, of RFC1331."
::= { pppLinkStatusEntry 4 }
pppLinkStatusPacketTooLongs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of received packets that have been
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 13]
Internet Draft PPP/LCP MIB July 1992
discarded because their length exceeded the
MRU. This counter is a component of the
ifInErrors variable that is associated with the
interface that represents this PPP Link. NOTE,
packets which are longer than the MRU but which
are successfully received and processed are NOT
included in this count."
::= { pppLinkStatusEntry 5 }
pppLinkStatusBadFCSs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of received packets that have been
discarded due to having an incorrect FCS. This
counter is a component of the ifInErrors
variable that is associated with the interface
that represents this PPP Link."
::= { pppLinkStatusEntry 6 }
pppLinkStatusLocalMRU OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current value of the MRU for the local PPP
Entity. This value is the MRU that the remote
entity is using when sending packets to the
local PPP entity."
::= { pppLinkStatusEntry 7 }
pppLinkStatusRemoteMRU OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current value of the MRU for the remote
PPP Entity. This value is the MRU that the
local entity is using when sending packets to
the remote PPP entity."
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 14]
Internet Draft PPP/LCP MIB July 1992
::= { pppLinkStatusEntry 8 }
pppLinkStatusLocalToPeerACCMap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current value of the ACC Map used for
sending packets from the local PPP entity to
the remote PPP entity."
::= { pppLinkStatusEntry 9 }
pppLinkStatusPeerToLocalACCMap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ACC Map used by the remote PPP entity when
transmitting packets to the local PPP entity."
::= { pppLinkStatusEntry 10 }
pppLinkStatusLocalToRemoteProtocolCompression
OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates whether the local PPP entity will
use Protocol Compression when transmitting
packets to the remote PPP entity."
::= { pppLinkStatusEntry 11 }
pppLinkStatusRemoteToLocalProtocolCompression
OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 15]
Internet Draft PPP/LCP MIB July 1992
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates whether the remote PPP entity will
use Protocol Compression when transmitting
packets to the local PPP entity."
::= { pppLinkStatusEntry 12 }
pppLinkStatusLocalToRemoteACCompression OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates whether the local PPP entity will
use Address and Control Compression when
transmitting packets to the remote PPP entity."
::= { pppLinkStatusEntry 13 }
pppLinkStatusRemoteToLocalACCompression OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates whether the remote PPP entity will
use Address and Control Compression when
transmitting packets to the local PPP entity."
::= { pppLinkStatusEntry 14 }
pppLinkStatusTransmitFcsSize OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The size of the Frame Check Sequence (FCS) in
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 16]
Internet Draft PPP/LCP MIB July 1992
bits that the local node will generate when
sending packets to the remote node."
::= { pppLinkStatusEntry 15 }
pppLinkStatusReceiveFcsSize OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The size of the Frame Check Sequence (FCS) in
bits that the remote node will generate when
sending packets to the local node."
::= { pppLinkStatusEntry 16 }
pppLinkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppLinkConfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table containing the LCP configuration
parameters for this PPP Link. These variables
represent the initial configuration of the PPP
Link. The actual values of the parameters may
be changed when the link is brought up via the
LCP options negotiation mechanism."
::= { pppLink 2 }
pppLinkConfigEntry OBJECT-TYPE
SYNTAX PppLinkConfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Configuration information about a particular
PPP Link."
INDEX { pppLinkConfigIndex }
::= { pppLinkConfigTable 1 }
PppLinkConfigEntry ::= SEQUENCE {
pppLinkConfigIndex
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 17]
Internet Draft PPP/LCP MIB July 1992
INTEGER,
pppLinkConfigInitialMRU
INTEGER,
pppLinkConfigReceiveACCMap
OCTET STRING,
pppLinkConfigTransmitACCMap
OCTET STRING,
pppLinkConfigMagicNumber
INTEGER,
pppLinkConfigFcsSize
INTEGER
}
pppLinkConfigIndex OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each PPP link. Its value
ranges between 1 and the value of ifNumber. The
interface identified by a particular value of
this index is that identified by the same value
of an ifIndex object instance. The value for
each link must remain constant at least from
one re-initialization of the entity's network
management system to the next
re-initialization."
::= { pppLinkConfigEntry 1 }
pppLinkConfigInitialMRU OBJECT-TYPE
SYNTAX INTEGER(0..2147483648)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The initial Maximum Receive Unit (MRU) that
the local PPP entity will advertise to the
remote entity. If the value of this variable is
0 then the local PPP entity will not advertise
any MRU to the remote entity and the default
MRU will be assumed. Changing this object will
have effect when the link is next restarted."
REFERENCE
"Section 7.2, Maximum Receive Unit of RFC1331."
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 18]
Internet Draft PPP/LCP MIB July 1992
DEFVAL { 1500 }
::= { pppLinkConfigEntry 2 }
pppLinkConfigReceiveACCMap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Asynchronous-Control-Character-Map (ACC)
that the local PPP entity requires for use on
its receive side. In effect, this is the ACC
Map that is required in order to ensure that
the local modem will successfully receive all
characters. The actual ACC map used on the
receive side of the link will be a combination
of the local node's pppLinkConfigReceiveACCMap
and the remote node's
pppLinkConfigTransmitACCMap. Changing this
object will have effect when the link is next
restarted."
REFERENCE
"Section 7.3, page 4, Async-Control-Character-
Map of RFC1331."
DEFVAL { 'ffffffff'h }
::= { pppLinkConfigEntry 3 }
pppLinkConfigTransmitACCMap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Asynchronous-Control-Character-Map (ACC)
that the local PPP entity requires for use on
its transmit side. In effect, this is the ACC
Map that is required in order to ensure that
all characters can be successfully transmitted
through the local modem. The actual ACC map
used on the transmit side of the link will be a
combination of the local node's
pppLinkConfigTransmitACCMap and the remote
node's pppLinkConfigReceiveACCMap. Changing
this object will have effect when the link is
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 19]
Internet Draft PPP/LCP MIB July 1992
next restarted."
REFERENCE
"Section 7.3, page 4, Async-Control-Character-
Map of RFC1331."
DEFVAL { 'ffffffff'h }
::= { pppLinkConfigEntry 4 }
pppLinkConfigMagicNumber OBJECT-TYPE
SYNTAX INTEGER {false (1), true (2)}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If true(2) then the local node will attempt to
perform Magic Number negotiation with the
remote node. If false(1) then this negotiation
is not performed. In any event, the local node
will comply with any magic number negotiations
attempted by the remote node, per the PPP
specification. Changing this object will have
effect when the link is next restarted."
REFERENCE
"Section 7.6, Magic Number, of RFC1331."
DEFVAL { false }
::= { pppLinkConfigEntry 5 }
pppLinkConfigFcsSize OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The size of the FCS, in bits, the local node
will attempt to negotiate for use with the
remote node. Regardless of the value of this
object, the local node will comply with any FCS
size negotiations initiated by the remote node,
per the PPP specification. Changing this object
will have effect when the link is next
restarted."
DEFVAL { 16 }
::= { pppLinkConfigEntry 6 }
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 20]
Internet Draft PPP/LCP MIB July 1992
5.2. PPP LQR Group
--
-- The PPP LQR Group.
-- Implementation of this group is mandatory for all
-- PPP implementations that implement LQR.
--
pppLqrTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppLqrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table containing the LQR parameters and
statistics for the local PPP entity."
::= { pppLqr 1 }
pppLqrEntry OBJECT-TYPE
SYNTAX PppLqrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"LQR information for a particular PPP link. A
PPP link will have an entry in this table if
and only if LQR Quality Monitoring has been
successfully negotiated for said link."
INDEX { pppLqrIndex }
::= { pppLqrTable 1 }
PppLqrEntry ::= SEQUENCE {
pppLqrIndex
INTEGER,
pppLqrQuality
INTEGER,
pppLqrInGoodOctets
Counter,
pppLqrLocalPeriod
INTEGER,
pppLqrRemotePeriod
INTEGER,
pppLqrOutLQRs
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 21]
Internet Draft PPP/LCP MIB July 1992
Counter,
pppLqrInLQRs
Counter
}
pppLqrIndex OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of ifIndex that identifies the entry
in the interface table that is associated with
the PPP Link entity over which this LQR is
operating."
::= { pppLqrEntry 1 }
pppLqrQuality OBJECT-TYPE
SYNTAX INTEGER {
good(1),
bad(2),
not-determined(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current quality of the link as declared by
the local PPP entity's Link-Quality Management
modules. No effort is made to define good or
bad, nor the policy used to determine it. The
not-determined value indicates that the entity
does not actually evaluate the link's quality.
This value is used to disambiguate the
determined to be good case from the no
determination made and presumed to be good
case."
::= { pppLqrEntry 2 }
pppLqrInGoodOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 22]
Internet Draft PPP/LCP MIB July 1992
"The LQR InGoodOctets counter for this link."
REFERENCE
"Section 2.2, Counters, of [12]."
::= { pppLqrEntry 3 }
pppLqrLocalPeriod OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The LQR reporting period, in hundredths of a
second that is in effect for the local PPP
entity."
REFERENCE
"Section 2.5, Configuration Option Format, of
[12]."
::= { pppLqrEntry 4 }
pppLqrRemotePeriod OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The LQR reporting period, in hundredths of a
second, that is in effect for the remote PPP
entity."
REFERENCE
"Section 2.5, Configuration Option Format, of
[12]."
::= { pppLqrEntry 5 }
pppLqrOutLQRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of the OutLQRs counter on the local
node for the link identified by
pppLqrLinkIndex."
REFERENCE
"Section 2.2, Counters, of [12]."
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 23]
Internet Draft PPP/LCP MIB July 1992
::= { pppLqrEntry 6 }
pppLqrInLQRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of the InLQRs counter on the local
node for the link identified by
pppLqrLinkIndex."
REFERENCE
"Section 2.2, Counters, of [12]."
::= { pppLqrEntry 7 }
--
-- The PPP LQR Configuration table.
--
pppLqrConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppLqrConfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table containing the LQR Configuration
parameters for the local PPP entity."
::= { pppLqr 2 }
pppLqrConfigEntry OBJECT-TYPE
SYNTAX PppLqrConfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"LQR configuration information for a particular
PPP link."
INDEX { pppLqrConfigIndex }
::= { pppLqrConfigTable 1 }
PppLqrConfigEntry ::= SEQUENCE {
pppLqrConfigIndex
INTEGER,
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 24]
Internet Draft PPP/LCP MIB July 1992
pppLqrConfigPeriod
INTEGER,
pppLqrConfigStatus
INTEGER
}
pppLqrConfigIndex OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value which ranges between 1 and the
value of ifNumber. The interface identified by
a particular value of this value is that
identified by the same value of an ifIndex
object instance. The value for each link must
remain constant at least from one
re-initialization of the entity's network
management system to the next
re-initialization."
::= { pppLqrConfigEntry 1 }
pppLqrConfigPeriod OBJECT-TYPE
SYNTAX INTEGER(0..2147483648)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LQR Reporting Period that the local PPP
entity will attempt to negotiate with the
remote entity, in units of hundredths of a
second. Changing this object will have effect
when the link is next restarted."
REFERENCE
"Section 2.5, Configuration Option Format, of
[12]."
DEFVAL { 0 }
::= { pppLqrConfigEntry 2 }
pppLqrConfigStatus OBJECT-TYPE
SYNTAX INTEGER {disabled (1), enabled (2)}
ACCESS read-write
STATUS mandatory
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 25]
Internet Draft PPP/LCP MIB July 1992
DESCRIPTION
"If enabled(2) then the local node will attempt
to perform LQR negotiation with the remote
node. If disabled(1) then this negotiation is
not performed. In any event, the local node
will comply with any magic number negotiations
attempted by the remote node, per the PPP
specification. Changing this object will have
effect when the link is next restarted.
Setting this object to the value disabled(1)
has the effect of invalidating the
corresponding entry in the pppLqrConfigTable
object. It is an implementation-specific matter
as to whether the agent removes an invalidated
entry from the table. Accordingly, management
stations must be prepared to receive tabular
information from agents that corresponds to
entries not currently in use."
REFERENCE
"Section 7.6, Magic Number, of RFC1331."
DEFVAL { enabled }
::= { pppLqrConfigEntry 3 }
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 26]
Internet Draft PPP/LCP MIB July 1992
5.3. PPP LQR Extensions Group
--
-- The PPP LQR Extensions Group.
-- Implementation of this group is optional.
--
-- The intent of this group is to allow external
-- implementation of the policy mechanisms that
-- are used to declare a link to be "bad" or not.
--
-- It is not practical to examine the MIB objects
-- which are used to generate LQR packets since
-- LQR policies tend to require synchronization of
-- the values of all data used to determine Link
-- Quality; i.e. the values of the relevant counters
-- must all be taken at the same instant in time.
--
pppLqrExtnsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppLqrExtnsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table containing extended LQR parameters local
PPP entity."
::= { pppLqr 3 }
pppLqrExtnsEntry OBJECT-TYPE
SYNTAX PppLqrExtnsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Extended LQR information for a particular PPP
link. Assuming that this group has been
implemented, a PPP link will have an entry in
this table if and only if LQR Quality
Monitoring has been successfully negotiated for
said link."
INDEX { pppLqrExtnsIndex }
::= { pppLqrExtnsTable 1 }
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 27]
Internet Draft PPP/LCP MIB July 1992
PppLqrExtnsEntry ::= SEQUENCE {
pppLqrExtnsIndex
INTEGER,
pppLqrExtnsLastReceivedLqrPacket
OCTET STRING(SIZE(68))
}
pppLqrExtnsIndex OBJECT-TYPE
SYNTAX INTEGER(1..2147483648)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value which ranges between 1 and the
value of ifNumber. The interface identified by
a particular value of this value is that
identified by the same value of an ifIndex
object instance. The value for each link must
remain constant at least from one
re-initialization of the entity's network
management system to the next
re-initialization."
::= { pppLqrExtnsEntry 1 }
pppLqrExtnsLastReceivedLqrPacket OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(68))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains the most recently
received LQR packet. The format of the packet
is as described in the LQM Protocol
specificiation. All fields of the packet,
including the `save' fields, are stored in this
object.
The LQR packet is stored in network byte order.
The LAP-B and PPP headers are not stored in
this object; the first four octets of this
variable contain the Magic-Number field, the
second four octets contain the LastOutLQRs
field and so on. The last four octets of this
object contain the SaveInOctets field of the
LQR packet."
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 28]
Internet Draft PPP/LCP MIB July 1992
REFERENCE
"Section 2.6, Packet Format, of RFC1333"
::= { pppLqrExtnsEntry 2 }
END
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 29]
Internet Draft PPP/LCP MIB July 1992
5.4. PPP Tests
The extensions to the interface table in [7] define a table
through which the network manager can instruct the managed
object to perform various tests of the interface. This is the
ifExtnsTestTable.
The PPP MIB defines two such tests.
5.4.1. PPP Echo Test
The PPP Echo Test is defined as
pppEchoTest OBJECT IDENTIFIER ::= { pppTests 1 }
Invoking this test causes a PPP Echo Packet to be sent on the
line. ifExtnsTestResult returns success(2) if the echo
response came back properly. It returns failed(7) if the
response did not properly return. The definition of "proper"
in this context is left to the discretion of the implementor.
5.4.2. PPP Discard Test
The PPP Discard Test is defined as
pppDiscardTest OBJECT IDENTIFIER ::= { pppTests 2 }
Invoking this test causes a PPP Discard Packet to be sent on
the line. ifExtnsTestResult returns success(2) if the discard
packet was successfully transmitted and failed(7) if an error
was detected on transmission. The definition of "transmission
error" in this context is left to the discretion of the
implementor.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 30]
Internet Draft PPP/LCP MIB July 1992
6. Acknowledgements
This document was produced by the PPP working group. In
addition to the working group, the author wishes to thank the
following individuals for their comments and contributions:
Bill Simpson -- Daydreamer
Glenn McGregor -- Merit
Jesse Walker -- DEC
Chris Gunner -- DEC
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 31]
Internet Draft PPP/LCP MIB July 1992
7. Security Considerations
The PPP MIB affords the network operator the ability to
configure and control the PPP links of a particular system,
including the PPP authentication protocols. This represents a
security risk.
These risks are addressed in the following manners:
(1) All variables which represent a significant security risk
are placed in separate, optional, MIB Groups. As the MIB
Group is the quantum of implementation within a MIB, the
implementor of the MIB may elect not to implement these
groups.
(2) The implementor may choose to implement the variables
which present a security risk so that they may not be
written, i.e., the variables are READ-ONLY. This method
still presents a security risk, and is not recommended,
in that the variables, specifically the PPP
Authentication Protocols' variables, may be easily read.
(3) Using the new SNMP administrative framework[13,14], the
operator can place the variables into MIB views which are
protected in that the parties which have access to those
MIB views use authentication and privacy protocols, or
the operator may elect to make these views not accessible
to any party. In order to facilitate this placement, all
security-related variables are placed in separate MIB
Tables. This eases the identification of the necessary
MIB View Subtree.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 32]
Internet Draft PPP/LCP MIB July 1992
8. References
[1] M.T. Rose and K. McCloghrie, Structure and Identification
of Management Information for TCP/IP-based internets,
Internet Working Group Request for Comments 1155.
Network Information Center, SRI International, Menlo
Park, California, (May, 1990).
[2] K. McCloghrie and M.T. Rose, Management Information Base
for Network Management of TCP/IP-based internets - MIB-2,
Internet Working Group Request for Comments 1213.
Network Information Center, SRI International, Menlo
Park, California, (March, 1991).
[3] Information processing systems - Open Systems
Interconnection - Specification of Abstract Syntax
Notation One (ASN.1), International Organization for
Standardization. International Standard 8824, (December,
1987).
[4] Information processing systems - Open Systems
Interconnection - Specification of Basic Encoding Rules
for Abstract Notation One (ASN.1), International
Organization for Standardization. International Standard
8825, (December, 1987).
[5] Rose, M., and K. McCloghrie, Editors, Concise MIB
Definitions, RFC 1212, Performance Systems International,
Hughes LAN Systems, March 1991.
[6] Rose, M., Editor, A Convention for Defining Traps for use
with the SNMP, RFC 1215, Performance Systems
International, March 1991.
[7] K. McCloghrie, Extensions to the Generic-Interface MIB,
RFC1229, Hughes LAN Systems, May 1991.
[8] W. Simpson, The Point-to-Point Protocol for the
Transmission of Multi-protocol Datagrams over Point-to-
Point Links, RFC 1331, May 1992.
[9] G. McGregor, The PPP Internet Protocol Control Protocol,
RFC 1332, Merit, May 1992.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 33]
Internet Draft PPP/LCP MIB July 1992
[10] F. Baker, Point-to-Point Protocol Extensions for
Bridging, RFC1220, ACC, April 1991.
[11] PPP Authentication Protocols, Work In Progress
[12] W. Simpson, PPP Link Quality Monitoring, RFC 1333, May
1992.
[13] New SNMP Administrative Model, Work In Progress.
[14] SNMP Security Protocols, Work In Progress.
[15] J. Case, Fedor, M., Schoffstall, M., and Davin, J., A
Simple Network Management Protocol, RFC1157, May 1990.
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 34]
Internet Draft PPP/LCP MIB July 1992
Table of Contents
Status of this Memo .................................... 1
1 Abstract .............................................. 2
2 The Network Management Framework ...................... 3
3 Objects ............................................... 4
3.1 Format of Definitions ............................... 4
4 Overview .............................................. 5
4.1 Object Selection Criteria ........................... 5
4.2 Structure of the PPP ................................ 5
4.3 MIB Groups .......................................... 6
4.4 Relationship to Interface and Interface Extensions
Groups ............................................. 8
5 Definitions ........................................... 10
5.1 PPP Link Group ...................................... 11
5.2 PPP LQR Group ....................................... 21
5.3 PPP LQR Extensions Group ............................ 27
5.4 PPP Tests ........................................... 30
5.4.1 PPP Echo Test ..................................... 30
5.4.2 PPP Discard Test .................................. 30
6 Acknowledgements ...................................... 31
7 Security Considerations ............................... 32
8 References ............................................ 33
Frank J. Kastenholz Exp. 1 Feb. 1993 [Page 35]